Full Face Helmet Arai TOUR-X4 Detour-Ii Red

Size	XXXS	XXS	XS	S	M	L	XL	XXL	XXXL
Circumference	49/50	51/52	53/54	55/56	57/58	59/60	61/62	63/64	65/66

Tour-X4

The Tour-X 4 must be one of the most versatile helmets ever: adventure, grand touring or off road, and without the peak looks pretty good on a naked bike too! No matter the riding conditions, the Tour-X 4 is ready for it. Can be used without visor with goggles, without peak but with visor, any way that suits you. Download Tour-X4 instruction manual.

Tour-X4 Features

General

Outer shell: Complex Fibre Laminate (CFL)

Complex Fibre Laminate (CFL) employs special fibre layers bonded by unique resins formulated by Arai, producing an extremely high fibre to low resin ratio. This carefully managed construction delivers strength, structural integrity and impact flexibility which allows the rounded outer shell to do its main job – deflect, absorb and disperse impact energy over the widest possible area.

Innovative peak

The Arai peak scavenges and forces air into the forehead vent ports for cooling while at the same time using multiple relief-ports to reduce “lifting” at higher speeds.

Ventilation

Tour-X4 Ventilation

Easy to clean diffusers create a strong venture vacuum at the rear. Dual intake for increased airflow and lower noise level. Under-peak air intake collects and directs cool air into the helmet. Closable chin vent controls the airflow to the chin area. Inner chin vent shutter prevents debris coming into the helmet industy riding conditions. Brow ventilation, lower side vents and neck roll exhaust.

Front ventilation

Dual intake

Designed for increased airflow and lower noise level, guiding fresh, cool air into the interior.

Brow vents

Fresh air can enter directly to the forehead area without the need for holes in this critical area of the shell and impact absorbing liner. For specific models the ventilation is extended to the temple area.

Three position chin vent

Three-position chin vent helps in demisting the visor and offering fresh, cool air to the rider.

Inner chin (bar) vent shutter

Open and close the chin bar vents from the inside to prevent debris coming into the helmet in dusty riding conditions.

Rear ventilation

Neck exhaust vent

To enhance hot-air extraction from the interior. Increases the ventilation effect at the lower part of the helmet.

Removable diffuser

Creates a tremendous amount of venturi vacuum at the rear. Can be easily removed (for cleaning) or replacement.

Side exhausts

Produce low pressure behind the rear vent for better hot air extraction. Integrated in the shell for better aerodynamics, reduce wind noise and prevent buffeting at speed. Inside, a small foam dam helps to absorb and diminish excessive noise, without reducing ventilation performance.

Aerodynamics

Pull Down Chin Spoiler

Helps minimize wind noise and also aids with the extraction of hot air from the face area. Provides additional deflection of road debris away from neck. Depending on the model the Chin Spoiler is retractable.

Visor

Pinlock insert lens

Effectively prevents misting and fogging of the visor, even under extreme wet and damp conditions. May be cleaned and changed easily.

Interior

Dry-Cool® Liner

Arai´s Dry-Cool® material transfers heat and moisture away from the rider quickly and efficiently.

Replaceable Cheek pads/Ear cups

Cheek pads/ear cups may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning, blot dry with a towel and let air dry completely before reassembly. Never machine wash or use heat to dry. Interior parts in different size thickness are available for a custom fit for every rider.

• Remove by taking the frontside out first
• Place back by inserting the backside first

Replaceable Interior

The complete interior may be easily removed. All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning and never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider.

Replaceable Chinstrap covers

All parts (replaceable or not) can be cleaned with lukewarm water and mild soap. Rinse well after cleaning and never dry in direct sunlight or near a heat source. Interior parts in different size thickness are available for a custom fit for every rider.

Facial Contour System (FCS)

To offer an even better snug fit and enhancing the comfort to the lower jaw, the Facial Contour System (FCS) works with a foam spring support in the cheek pad that compresses and rebounds, providing the necessary support without excessive pressure.

5mm ’’Peel Away’’ Ear cups/Cheek pads

Giving even more ability to craft the perfect fit and comfort, the cheek pads feature a 5 mm peel away layer for added room if needed.

5mm ’’Peel Away’’ Temple pad

Arai´s peel-away temple crown pads give the option of 5 mm more interior width if needed.

Comfort

Emergency Release System (ERS)

Allows easier access to an injured rider. By pulling the orange tabs integrated in the pads, the cheek pads slide out. Making helmet removal easier for trained medical personnel and rescuers. Minimising the risk of additional injury.

Arai Features

Glancing Off

To minimize impact energy getting into the helmet, it’s crucial that a helmet can slide over a surface. Arai believes that a Strong, Round & Smooth shell helps to increase a helmets ability to protect the rider during an impact. Shells with sharp edges or vent ducts that don’t break off can reduce the helmet’s ability to slide, sending energy into the helmet, or even enhance rotational energy.

Five times inspected

Each Arai helmet goes through five separate quality-control depart­ments: after the shell is made, after painting and graphic completion, after assembly and two in-process inspections.

Washable interior

The premium quality interior of any Arai helmet can be easily cleaned, in place, with mild soap and lukewarm water.

Handmade

It can take up to five years for our experts to earn the right to create an Arai shell. Each shell can take up to 27 steps and to build one Arai helmet will take about 18 man-hours.

All-day comfort

All-day comfort with the Arai interior fit and shape together with the finest liner materials and the extensive ventilation system. And thanks to the perfect balance and weight distribution of the helmet, you hardly notice you are wearing an Arai.

Penetration tested

All Arai helmets are penetration tested, although not required by European helmet standards. The Arai penetration test is performed with a 3kg test cone that strikes from a height of 3m on the helmet.

Double-D ring device

The flat and D-shaped rings fit smooth against the chin. No moving parts, no corrosion problems and just pulling the tab is enough to loosen the fastener.

Smooth shape, better protection

The smooth outer shell of Arai helmets is designed to glide without unnecessary resistance. You don’t want to decelerate your helmet more than necessary. That’s why all Arai vents and ducts are designed to break off during an impact.

Strong outer shell, soft inner shell

Arai uses a very strong outer shell to spread impact forces and a soft inner shell to absorb remaining energy. The multiple-density EPS inner shell is made using a unique technology of combining three to five densities in various areas as a single component.

Organic shape

The organic shape of an Arai outer shell offers a more natural appearance, seals better and conforms more to the head’s natural shape for improved comfort, fit and to help minimize wind turbulence.

5-year limited warranty

All Arai helmets are warranted against defects in materials and workmanship, and are serviceable only for the properly fitted first user for 5 years from date of first use, but no more than 7 years from date of manufacture.

Different outer shells

Unlike many other manufacturers Arai provides one size outer shell for each two-helmet sizes for most models. Together with different shaped outer shells for different models it is almost impossible not to find the fit you are looking for.

Arai In-house Test

Arai helmets are designed to meet the stringent Arai In-house criteria, in addition to the mandatory ECE standard.

Approval

ECE 22-05

The most common helmet certification internationally, required by over 50 countries worldwide.